学術雑誌論文

１）淵澤　定克，白寄　篤，山本　裕孝，奈良崎　道治：
　　「軸押込みと内圧による薄肉銅管のバルジ加工」
　　　塑性と加工（日本塑性加工学会誌）35巻398号(1994)，250-255．

２）S. Fuchizawa, M. Narazaki, A. Shirayori :
     "Bulge Forming of Aluminum Alloy Tubes by Internal Pressure and Axial
      Compression"
      Advanced Technology of Plasticity vol.Ⅰ (Proc. 5th Int. Conf. on
      Technol. of Plasticity), Columbus, USA (1996), 497-500．

３）白寄　篤，淵澤　定克，奈良崎　道治，田中　伸司：
　　「内圧を受けて自由バルジ変形する角管の変形挙動
　　　―　液圧バルジ加工における角管の変形　Ⅰ　―」
　　　塑性と加工（日本塑性加工学会誌）39巻449号(1998)，613-617．

４）A. Shirayori，S. Fuchizawa，M. Narazaki：
     "Experimental Investigation into a Tube Forming Method for
      Providing Tubes with Thickness Distribution in Axial Direction"
      Advanced Technology of Plasticity Vol.Ⅱ (Proc. 6th Int. Conf. on
      Technol. of Plasticity), Nuremberg, Germany (1999)，1223-1228．

５）Atsushi Shirayori, Sadakatsu Fuchizawa, Michiharu Narazaki：
　　 "Influence of Initial Thickness Deviation in Tube Periphery on
      Tube Deformation during Free Hydraulic Bulging"
      Transactions of North American Manufacturing Research Institution of SME
      Vol. 30(2002),111-118.

６）A. Shirayori, S. Fuchizawa, M. Narazaki :
     "Influence of Initial Thickness Deviation on Tube Deformation
      during Free Hydraulic Bulging"
      Advanced Technology of Plasticity Vol.2 (Proc. 7th Int. Conf. on
      Technol. of Plasticity), Yokohama, Japan (2002), 1459-1464.

７）A. Shirayori，S. Fuchizawa，H. Ishigure，M. Narazaki：
     "Deformation Behavior of Tubes with Thickness Deviation
　　　in Circumferential Direction during Hydraulic Free Bulging"
      Journal of Material Processing Technology, Vol. 139(2003), 58-63.

８）Atsushi Shirayori :
     "Dealing with internal pressure in free hydraulic bulging"
      The Tube & Pipe Journal Vol. 14, No. 3 (April/May 2003), 56-60．

 ９）Atsushi Shirayori, Sadakatsu Fuchizawa, Michiharu Narazaki：
　　 "A Design Method of Loading Paths for Tube Hydroforming
      using FEM Simulator"
      Transactions of North American Manufacturing Research Institution of SME
      Vol. 32(2004),629-636.

10）Atsushi Shirayori, Sadakatsu Fuchizawa, Michiharu Narazaki：
　　 "Influence of Axial Feeding on the Growth of Circumferential Thickness
      Deviation in Free Hydraulic Bulging"
      METALS and MATERIALS International Vol. 13, No. 2 (2007),185-189.

11）Arif Sugianto, Michiharu Narazaki, Minoru Kogawara, Atsushi Shirayori：
　　 "Failure analysis and prevention of quench crack of eccentric holed
      disk by experimental study and computer simulation"
      Engineering Failure Analysis, Vol. 16(2009.1), 70-84.

12）Arif Sugianto, Michiharu Narazaki, Minoru Kogawara, Atsushi Shirayori,
    Soo-Young Kim, Satoshi Kubota：
　　 "Numerical simulation and experimental verification of carburizing-quenching
      process of SCr420H steel helical gear"
      Journal of Material Processing Technology, Vol. 209(2009.4), 3597-3609.

13）Arif Sugianto, Michiharu Narazaki, Minoru Kogawara, Atsushi Shirayori：
　　 "A compatative study on determination method of heat transfer coefficient
      using inverse heat transfer and iterative modification"
      Journal of Material Processing Technology, Vol. 209(2009.6), 4627-4632.

14）Atsushi Shirayori, Michiharu Narazaki :
     "Hydraulic Bulge Forming of Small Diameter Tubes"
　    steel reseach international (Proceedings of the 13th International Conference
      on Metal Forming METAL FORMING 2010), vol.81 no.9 (2010.9)，528-531．

戻る